Carbon Dioxide Separation And Recovery Technology

May 24, 2025

Leave a message

Global energy consumption is increasing in the process of modern industrial development, among which natural gas, oil, coal, and other fossil energy consumption are the largest. Since the Industrial Revolution in 1860, CO2 emissions have been increasing year by year. According to the objective forecast report of the Energy Information Administration (EIA) of the U.S. Department of Energy, the total global CO2 emissions may reach or exceed 45 billion tons in 2030. The large and accelerated emission of CO2 will not only further aggravate the greenhouse effect and cause global warming, but also seriously damage the ecological balance and cause various ecological and environmental problems, which will eventually cause harm to humans. In Berlin in 2014, the fifth assessment report officially released by the Intergovernmental Panel on Climate Change (IPCC) of the United Nations mentioned that the growth trend of global greenhouse gas emissions has reached an unprecedented level. In the absence of emission reduction measures, the global average temperature is expected to be 3.7~4.8℃ higher than before the Industrial Revolution in 2100. Carbon dioxide is an important carbon resource. It can be used as a raw material for synthesizing organic matter, as an auxiliary agent for the exploitation of oil and natural gas, and as an extractant for extracting organic matter in a supercritical state. Therefore, how to effectively separate and recycle CO2 emitted by fossil energy and reuse it as a resource has become one of the important issues for achieving sustainable development in modern society.

 

Keywords: carbon dioxide; separation and recovery technology; resource utilization

Production of carbon dioxide

 

The sources of CO2 are very widespread and can be roughly divided into the following emission sources.
1) Emissions from hydrogen production in chemical plants. Refineries, fertilizer plants, and other organic chemical plants require H2 for production, which is usually converted from methane, carbon monoxide, carbon, and other substances after fusion with water vapor. During the conversion process, CO2 and H2 are generated, of which about 15% is CO2. Most of the generated CO2 will be directly discharged into the atmosphere in the form of tail gas.

2) Emissions from ore decomposition. Calcium oxide is used in the production of soda ash, coatings, and steelmaking, and is usually obtained by heating limestone for decomposition; magnesium oxide is used in the production of refractory bricks and magnesia bricks. Magnesium oxide is almost derived from heating magnesium ore, and these heating decomposition processes will have a large amount of CO2 discharged.

3) Oil and gas fields. When mining natural gas and oil, mixed oilfield gas containing CO2 is often encountered, and the content is generally high, at least 20% and up to 99%.

4) Food, biochemical, and pharmaceutical industries. During the production process of beer and liquor using the fermentation method to produce alcohol, a large amount of CO2 gas is generated, with a content as high as 90%~98%, which is a relatively high-concentration CO2 gas source.

 

Carbon dioxide separation and recovery technology

 

Physical absorption method


Physical absorption method refers to the use of organic solvents to separate and absorb acid gas components under pressure according to the different solubility of components, and to achieve solvent regeneration by lowering the pressure, so it does not require too much regeneration energy. The key to the effective application of this method is to select high-quality absorbents. The quality standards are high boiling point, large CO2 solubility, non-corrosive, non-toxic, and stable chemical properties. At present, the commonly used absorbents are sulfolane, tributyl phosphate, propylene carbonate, methanol, and N-methylpyrrolidone.

 

The principle of this method is that CO2 in the raw gas shows a higher solubility in the absorbent, and the solubility of other gases is relatively much smaller. CO2 is removed based on this physical difference. It is often used in solute gases with high partial pressure, absorption under high pressure and low temperature, and desorption under low-pressure heating control. Low-pressure heating is the most effective way to reduce energy consumption.

 

Chemical absorption method

 

Chemical absorption method also uses absorbent, but the absorption and separation of CO2 mainly depends on the chemical reaction between absorbent and CO2. After a series of reactions, the absorbent in the absorption tower and the CO2 in the raw gas will be enriched with a large amount of CO2 centered on the absorption solvent. After the formation of this rich liquid, it will be heated in the desorption tower and finally decomposed to release CO2.

 

In practical applications, the absorbents used more often include alkaline solvents such as hot potassium carbonate, sodium hydroxide, calcium hydroxide, and different types of amine solutions. Because the absorption and desorption of steric histamines are not too difficult, they are widely used in the separation of CO2 by absorption. The CO2 absorption rates shown by various types of amine-based solvents are different. Compared with primary amines and secondary amines, the reaction rate of tertiary amines is much lower, mainly because there is no directly connected hydrogen proton on the nitrogen atom of tertiary amines. Steric histamines have multiple non-chain substituents on the nitrogen atom structure, such as 2-amino-2-methyl-1-propanol (AMP). When facing the same CO2 reaction, it is faster than tertiary amines and slower than secondary amines and primary amines with chain substituents. The large CO2 load is the biggest advantage of tertiary amines and sterically hindered amines. Relevant scholars have compared and studied the absorption of CO2 by several amines, specifically diisopropanolamine (DIPA), monoethanolamine (MEA), diethanolamine (DEA), N-methyldiethanolamine (MDEA), and 2-amino-2-methyl-1-propanol (AMP). The results show that the different concentrations of amine solutions will affect the specific reaction rate. When the concentration of amine-based solvents is high, the reaction rates of several amines are ranked as MEA>DEA>AMP>DIPA>MDEA, and kinetics plays an important role in this process; when the concentration of amine-based solvents is low, the characteristics of the amines carrying CO2 load can be seen, and the reaction rate ranking at this time is MEA>AMP>DEA>DIPA>MDEA.

 

Membrane separation method

 

The realization of membrane separation technology mainly depends on the different permeabilities of different components through polymer membranes. When facing gas crossing, the membrane made of polymer materials will achieve gas separation according to the difference in permeability. Pressure difference is the driving force of membrane separation. Only with the existence of a pressure difference can gas components with higher permeability pass through the membrane and be separated in the form of permeation gas flow. Most gases with low permeability will stay on the air inlet side of the membrane.

 

The membrane materials currently used for CO2 membrane separation are mainly polysulfone membrane, cellulose acetate membrane, polypeptide membrane, polyethersulfone membrane, and polyamide membrane, which are especially suitable for separating and recovering CO2 produced in the process of natural gas and oil mining. However, the heat resistance of these membranes is not very good. Although the heat resistance temperature of the polyamide membrane itself has reached the maximum value of 300℃, it can only reach the maximum operating temperature of 50℃ in actual application due to the limitation of the membrane component-related materials. Since the structure of the membrane separation device is relatively simple, the cost required is much lower than that of the solvent absorption method, but the purity of CO2 gas obtained in the end is not high. We can try to combine the two separation and recovery technologies to form a fusion mode of fine separation and coarse separation, reduce the overall energy consumption, and control investment costs.

 

Pressure swing adsorption separation method

 

Pressure swing adsorption is a dry process that has been mainly used in CO2 removal in recent years. The basic principle of this method is that the adsorption force, adsorption rate, and adsorption driving force of the adsorbent facing different gases are different, and the change of pressure value will cause the adsorption capacity to fluctuate. These characteristics are used to give pressurized treatment to achieve the adsorption separation of mixed gases, and then the adsorbent is regenerated by lowering the pressure. In this way, the gas can be separated and the adsorbent can be used cyclically.

 

Pressure swing adsorption has many advantages in actual separation and recovery treatment. Low energy consumption and low working pressure are the most prominent advantages; considering that pressure swing adsorption is more suitable for gas-solid separation, there is no need to consider the problem of solvent recovery and solvent consumption, and the adsorbent can have a long service life; the operation of the adsorption device can be completed completely automatically.

 

Previously, relevant researchers proposed to use pressure swing adsorption to remove CO2 from a nitrogen mixed gas. In the experimental operation, the first step is to select an adsorbent with extremely high CO2 adsorption and adsorption capacity. In strict accordance with the requirements of relevant technical indicators, the experimental data is calculated through the model to complete the preliminary design of the process. The object of the experiment is the pressure swing adsorption decarbonization of methanol vapor reforming cracking gas. The pressure swing adsorption operation steps are clarified based on the reasonable selection of decarbonization adsorbents. The final results show that by purifying hydrogen and removing CO2 in this way, a hydrogen purity of 99.99% and a recovery rate of 92% can be achieved, which greatly improves the hydrogen recovery rate compared with similar devices, which means that resource utilization can create more significant economic benefits.

 

Desulfurization and dehydrogenation cryogenic distillation method

 

Compared with the solvent adsorption method, the cryogenic distillation production process is more suitable for gas sources with high CO2 content, such as CO2 gas field sources, where the CO2 content is basically around 70%, and the rest is CH4, N2, and other gases. The cryogenic distillation method is very suitable for high-concentration gas sources with a content of more than 60%. Usually, gas field development will use the cryogenic distillation process to build a special CO2 gas processing plant that collects from the purifying and liquefying gas wells to achieve resource utilization and produce some CO2 products with high liquid purity values. The complete process system for producing liquid CO2 by cryogenic distillation includes processing units such as separation of raw gas, desulfurization, dehydration, liquefaction of refrigerant, distillation and dehydrogenation, and storage of products.

 

Principle and process of cryogenic distillation: The key to the production of liquid CO2 technology is to purify CO2 gas, completely remove H2O, H2S, and hydrocarbon impurities, and turn the raw gas into high-concentration CO2 gas. The process of purifying CO2 gas is relatively complex and technically difficult. The choice of process type will vary according to the pressure, composition, and temperature of the CO2 gas field, but no matter which process is used, the unit combination is the same that is, separation of raw materials, dehydration, desulfurization, liquefaction, distillation, and dehydrocarbonization. Under normal circumstances, the application process of cryogenic distillation process in CO2 gas separation and recovery is to first load the raw gas into the separator, then remove the sulfur in the raw gas and enter the desulfurization tower, and complete the water removal through the molecular sieve dehydration unit, and then reach the refrigeration system to receive cold liquefied CO2 treatment. The last step is to remove hydrocarbon impurities in the distillation unit. The cryogenic storage tank is used to store the liquefied CO2 product, and the market sales are completed in the form of bottling or tank trucks.

 

Comprehensive Utilization of Carbon Dioxide

 

Chemical production

 

The production of soda, carbonated beverages, beer, and other products in the light industry cannot be separated from carbon dioxide as a raw material. In addition, it can also be used in the organic synthesis of various chemical raw materials. In addition to the known and relatively mature chemical utilization sector, carbon dioxide is used in the production of methanol, combined hydrogen synthesis of dimethyl ether, and combined methanol catalysis and propylene oxide synthesis of dimethyl carbonate.

 

Gas fertilizer

 

Based on photosynthesis, plant chlorophyll absorbs CO2 from the air and produces plant starch. Under this natural law, CO2 is used as a resource to make gas fertilizer, and the CO2 concentration in the plant growth space is appropriately increased to achieve the goal of increasing production. Previously, agricultural science academies and related enterprises in various places have developed CO2 gas fertilizers and vigorously promoted them in local agricultural planting. According to relevant statistics, the increase in the production of vegetables using gas fertilizers is 20%~40%/mu. It takes about 100,000 yuan to complete the construction of a 3~5 kt/a CO2 gas fertilizer device. Under effective operation, it can achieve an annual profit of millions, so there is huge room for development. The use of CO2 in plant gas fertilizer can improve photosynthesis efficiency, increase yield, and effectively improve quality.

 

Beer and Beverages

 

Both the stimulating taste and the foaming of carbonated beverages, such as beer and beverages are derived from carbon dioxide. The taste differences of different beverages are closely related to the amount of carbon dioxide used in the production process. Ensuring the two conditions of low-temperature liquid and pressurization in the production process can accelerate the dissolution of carbon dioxide, which is specifically manifested as carbonation. When the lid is opened for drinking, carbon dioxide vaporizes due to the increase in temperature. The vaporization process absorbs heat and takes away some of the body's heat, allowing the drinker to feel different degrees of coolness.

 

Food industry

 

The main application effect of CO2 in the food industry is food preservation. The international community generally regards the CO2 natural oxygen reduction method as a preservation method with distinct modern characteristics. Specifically, CO2-controlled atmosphere preservation involves injecting high concentrations of CO2 into the fruit and vegetable storage environment to reduce the O2 content and inhibit the respiration of fruit and vegetable microorganisms. The reason why this method is widely welcomed by the market is that it does not use chemical preservatives. In a previous study, South China Agricultural University found that the use of CO2-controlled atmosphere to store litchi, the gas concentration range is controlled from a minimum of 15% to a maximum of 30%, and after 30 days, the litchi can still maintain its original flavor and color. When eggs are placed in a CO2 gas with a concentration of 30% to 40%, CO2 can enter the eggshell after 7 to 10 days, slowing down the formation of watery protein and playing a role in preservation. Whether it is taste, nutrition, texture, or appearance, they can remain unchanged when thawing refrigerated food, especially without chemical preservatives. This is the biggest advantage of CO2 in food refrigeration and preservation. Dry ice is used in aviation, food freezing and preservation, and supermarket vegetable preservation.

 

Medical field

 

One of the key factors that stimulates human breathing is carbon dioxide, which stimulates the respiratory center based on the stimulation of the human body's external chemoreceptors. If the human body inhales high-purity oxygen for a long time, it will stop breathing due to the reduction of carbon dioxide concentration, facing a great life-threatening danger. From a clinical medical perspective, when dealing with severe carbon monoxide, alkalosis, or shock, a mixture of 95% oxygen and 5% carbon dioxide is often used for auxiliary treatment. In addition, carbon dioxide is often used in cryogenic surgery.

 

Summary

 

With greenhouse gas emissions increasing year by year and global warming, NEWTEK attaches great importance to reducing greenhouse gas emissions. At the same time, it is committed to the development of new energy, reducing greenhouse gas emissions from the source, and reasonably recycling and reusing existing emissions. It is necessary to innovate based on existing separation technology and use higher separation recovery rates to support the development of carbon dioxide resource utilization, promote socially sustainable development, and enhance social and economic benefits.

 

Send Inquiry