Latest Applications Of Amino Compounds in Capture

May 28, 2025

Leave a message

Due to CO₂ emissions from human production and daily activities, the atmospheric CO₂ concentration has increased from 280 ppmv at the beginning of the Industrial Revolution to 379 ppmv in 2005, and this figure has now risen to 390 ppmv<sup>2</sup>. As the impacts of increasing CO₂ levels become increasingly severe, the development of effective CO₂ capture technologies has become a hot topic in the chemical community. Current CO₂ capture methods primarily include absorption, adsorption, and membrane separation. Among them, the absorption method is further divided into physical absorption and chemical absorption:


Physical absorption uses high-boiling-point solvents (e.g., ethanol, polyethylene glycol) to absorb and desorb CO₂ by continuously adjusting pressure and temperature between CO₂ and the absorbent, thereby achieving CO₂ separation.


Chemical absorption relies on chemical reactions between the raw gas and the absorbent to capture CO₂.


The adsorption method has emerged as a highly promising separation and recovery technology due to its advantages of simple process, low energy consumption, ease of automation, and non-corrosiveness. The membrane separation method separates CO₂ based on the differential permeation rates of CO₂ and other gas components through membrane materials. Amino groups are applied in nearly all of the above CO₂ capture methods. This study reviews the applications of amino groups in absorption, adsorption, and membrane separation, with a specific focus on their role in adsorption-based CO₂ capture.

 

Key words: amino modification, capture, adsorbent

Method for absorbing CO2 with an alcohol amine solution

 

The alcohol amine solution method is the most common and efficient method for absorbing CO2 in industrial applications. The alcohol amine molecule contains at least one hydroxyl group that can reduce the vapor pressure of the compound, and this hydroxyl group can also provide the necessary alkaline environment; the alcohol amine molecule should also contain an amino group that can promote the absorption of acidic gases.

 

At present, the research focus of the alcohol amine method for CO2 absorption is mostly concentrated on the process conditions of CO2 absorption, and there is less research on the mass transfer of the absorption process. A gas-liquid enhancement device was added to the process of DEA absorbing CO2 to study the effect of gas and liquid phase stirring enhancement on the mass transfer performance between the gas and liquid phases. When the gas phase stirring increased from 50r/min to 200r/min, the mass transfer coefficient increased from 0.0154 kmol/(s·m2·MPa) to 0.021 kmol/(s·m2·MPa), an increase of 36.3%. When the liquid phase stirring increased from 150r/min to 300r/min, the relative mass transfer coefficient increased from 0.009 kmol/(s·m2·MPa) to 0.021 kmol/(s·m2·MPa), an increase of nearly 134%. Experiments have shown that adding a gas-liquid enhancement device can improve the mass transfer capacity within a larger range, thereby further improving the absorption rate of CO2.

 

In addition to its high CO2 absorption capacity, the absorption of CO2 by alcohol amine solution also has some inevitable defects:
(1) It is difficult to separate the alcohol amine solution from CO2 after combining with it, and it needs to be separated at a higher temperature, which consumes a lot of energy;
(2) Alcohol amine solution will cause serious corrosion;
(3) Alcohol amine solution is easy to volatilize during CO desorption, which reduces its ability to absorb CO2;
(4) Alcohol amine solution is easy to undergo thermal degradation and oxidative degradation during CO2 desorption, which reduces its absorption capacity for CO2. It is precisely because of the above defects that scientific researchers are studying and developing new methods and materials that can be used to replace alcohol amine solution to capture CO2, such as the mixed alcohol amine solution method, the amine optimized membrane separation method, and the amino modified adsorbent.

 

Method for adsorbing CO2 using amino-modified adsorbent

 

The key to the adsorption method is the adsorbent. Conventional adsorbents include molecular sieves, activated carbon, etc., while new adsorbents include carbon nanotubes, graphene, metal organic framework materials, mesoporous materials, etc. Each method has its own advantages and limitations, and each material also has its own applicable fields and defects. The use of composite materials or optimized new methods that combine the advantages of various materials will be a trend in capturing CO2, and has great research potential. This study takes amino-modified metal-organic framework materials, amino-modified mesoporous materials, amino-modified carbon nanotubes, and amino-modified graphene as examples to introduce amino-modified adsorbents in the field of capturing CO2.

 

Amino-modified metal-organic frameworks

 

As a new adsorbent for capturing CO2, MOFS has very obvious advantages over conventional molecular sieves (zeolite molecular sieves, carbon molecular sieves, etc.) and alcohol amine solutions. First, the framework of most MOFs is neutral, so the guest molecules occupying the pores have only weak interactions with the skeleton. These guest molecules can be driven out of the skeleton at a lower temperature, and the required pores can be quickly generated while maintaining the integrity of the skeleton. Secondly, the size, distribution, hydrophilicity, and chemical functionality of the pores of MOFs can be designed at the molecular level by changing or modifying the organic ligands and metal ions used.

 

To improve its ability to adsorb CO2, amino-modified metal organic framework materials are currently commonly assembled with organic ligands with amino groups and metal arrowheads. Blom prepared three MOF materials, USO-1-A1, USO-2-Ni, and USO-3-I,n and the corresponding amino-modified MOF materials (USO-1-AI-A, USO-2-Ni-A, and USO-3-In-A). The results of the CO2 adsorption test showed that the crystallinity, specific surface area, and pore volume of the amino-modified materials were reduced to varying degrees, while the adsorption effect was significantly improved. Taking USO-1-A1 and USO-1-AI-A as examples, at 25℃ and 1atm, the CO2 adsorption capacity of USO-1-AI was 2.3mmol/g, while that of USO-1-A1-A was increased to 2.7mmol/g; the initial adsorption heat of CO2 increased from 30kJ/mol to 50kJ/mol, which confirmed that the adsorption of CO2 by the amino-modified materials was significantly enhanced.

 

Amino-modified mesoporous materials

 

Although metal-organic framework materials and molecular sieves are good adsorption materials, the inherent diffusion of the microporous system limits the adsorption capacity of CO2 to a certain extent. Some SiO2 mesoporous materials can reduce the impact of this diffusion effect and improve the adsorption capacity. However, some residual hydroxyl groups on the surface of SiO2 make the material less compatible with CO2. This problem can be overcome by combining amino-containing organic compounds with the pores of mesoporous materials through impregnation or grafting.

 

50% polyethyleneimine was loaded into the pores of MCM-41 by impregnation. The adsorption capacity of amine-modified MCM-41 for CO2 reached 133 mg/g at 348K, which is higher than the 78 mg/g obtained with silica gel as the carrier.

 

Amino-modified carbon nanotubes

 

In recent years, the development of new materials has affected all aspects of people's lives. The application of carbon nanotubes in the field of gas separation has become an active highlight. Carbon nanotubes have typical layered hollow structure characteristics, and the fixed distance between layers is conducive to amino loading.

 

After CNTs were surface modified with 3-aminopropyltriethoxysilane (APTS), their CO adsorption capacity and thermodynamic properties were studied. When the temperature was set at 50℃, the unmodified CNTs (APTS) with ATPS and CNTS mass ratios of 20%, 28%, 36%, 41%, 45% and 54% were adsorbed in a 15% CO2 environment, and the adsorption amounts were 21.5mg/g, 43.6mg/g, 51.3mg/g, 60.5mg/g, 74.5mg/g, 85.7mg/g and 77mg/g, respectively. These data show that due to the presence of amino groups in ATPS, the introduction of APTS on the CNTS surface can significantly improve the CO adsorption capacity. And when the ATPS loading is 45% (wt, mass fraction, the same below), the maximum adsorption amount of C is reached, which is 4 times that of unmodified CNTs. However, when the loading amount continued to increase to 54%, the adsorption amount decreased instead. This may be because too much APTS on the surface of CNTs increased the mass transfer resistance of CO2 diffusing into the interior.

 

These research reports confirm that the ability of carbon nanotubes modified with amino groups to adsorb CO2 is significantly better than that of unmodified carbon nanotubes. Carbon nanotubes modified with amino groups show good prospects in capturing CO2, but their application and development space are limited due to their high cost.

 

Amino-modified graphene

 

The crystal structure of the graphene surface is very complete, which makes its chemical properties inactive. In order to expand the application range of graphene and improve its application value, its surface needs to be modified. The functional groups generated after graphene oxidation increase the activity of graphene, laying the foundation for covalent modification. Then, the surface functionalization of graphene can be achieved by modifying it with reagents such as organic amines and isocyanates.

 

In 2012, Mishra et al. first modified the surface of graphene with polyaniline (PANI) to capture CO and found that the modified graphene had a higher CO2 adsorption capacity than activated carbon, zeolite, metal-organic framework materials and carbon nanotubes. They also studied and compared the adsorption isotherms of the polyaniline-modified materials and unmodified graphene. When the pressure was 11 bar and the temperature was 25℃, 50℃ and 100℃, the adsorption amount of CO2 by the modified material PANI-f-HEG was 75mmol/g, 47mmol/g and 31mmol/g respectively; while the adsorption amount of unmodified pure graphene HEG was 21.6mmol/g, 18mmol/g and 12mmol/g. Although the research on the adsorption of CO2 by amino-modified graphite has just begun, it has shown great application potential and development space in this regard. Perhaps this will become a new direction for the development of CO2 adsorption materials.

 

Examples such as amino-modified metal-organic framework materials, amino-modified mesoporous materials, amino-modified carbon nanotubes, and amino-modified graphene have proven that these adsorbents have shown good CO2 capture capabilities after being modified with amino groups, and have changed from simple physical adsorption to chemical adsorption with amino groups as active centers. This has opened up a new field for studying adsorbents and is likely to become a focus of future research.

 

Amine-optimized membrane separation technology for CO2 adsorption

 

Membrane separation is similar to the screening process. According to the pore size of the membrane, some substances can pass through the membrane while other substances are retained by the membrane, thereby achieving the purpose of separation. The biggest disadvantage of membrane separation in gas separation is that the selectivity is not high. If you want to improve the selectivity of membrane separation and improve the separation efficiency, you can combine membrane separation with absorption or adsorption. First, use membrane separation to roughly separate the gas, and then use alcohol amine solution absorption or high-efficiency adsorbent adsorption for fine separation. This can not only achieve a certain separation effect, but also save investment costs. Combine membrane separation technology with alcohol amine solution absorption method, let the gas flow along one side of the membrane, and when CO2 diffuses to the other side of the membrane, it is absorbed by alcohol amine. This amine-optimized membrane separation method has a simpler device and lower investment cost than the alcohol amine solution absorption method. In addition, compared with the traditional membrane separation method, the ability to adsorb CO2 is significantly improved. Compared with the adsorption method and the alcohol amine easy absorption method, the amine-optimized membrane separation method has the advantages of easy operation, low energy consumption, better adsorption effect and less investment. However, due to the immaturity of technology and the fact that replacing equipment still consumes a lot of money, it has not been industrially applied.
 

Conclusion

 

The absorption of CO2 by organic amines using chemical absorption is the most common method in industrial applications, but this method requires a large investment, high energy consumption, a complex process, and high equipment corrosion. Adsorption separation of CO2 is an economical and environmentally friendly method, but the development of efficient adsorbents is the core. Membrane separation technology has a simple process, large operational flexibility, and low investment cost, but the service life of the membrane is short. If you want to efficiently separate CO2, you must combine it with solvent absorption or adsorption. Looking at these methods, they all have their advantages and limitations, and each material also has its applicable fields and defects. The use of "1+1>2" composite materials or optimized new methods that combine the advantages of various materials will be a trend in capturing C02, and has great research potential. In the development of new materials and the optimization of separation methods, amino groups have shown good compatibility. Its application involves almost all methods, which can greatly improve the ability to capture CO2 and has high research value.

 

Send Inquiry